GOLD control began to produce solid state relay and SCR power controller since 1992.

GOLD SSR, 60A DC SSR, DC control DC solid state relay, input 4-32VDC, input with LED indication, output current capacity 60A, output voltage 12-480VDC· Ratings from 10A to 60A @ 12-280 VDC· 600 Volts transient overvoltage· Removable IP 20 touch-safe cover· Easy-to-use thermal pad· Strengthened current design for heavy industrial loads· Input LED status indicator· CE approved, RoHS/EMC compliant.

·AC output proportional controller·Rating from 10A to 80A @ 120 VAC, 220 VAC or 400 VAC·2 to 10 VDC or 4 to 20 mA DC control·Removable IP 20 touch-safe cover·Easy-to-use thermal pad·CE approved, RoHS/EMC compliant.·Designed in according with the requirements of IEC 62314·Mainly for resistive loads·For transformer loads, control output voltage range is 80-100% of rated voltage.

· Ratings from 100A to 300A @ 40-480 VAC· 1200 Volts transient overvoltage· Removable IP 20 touch-safe cover· LED input status indicator· UL/CE approved, RoHS/EMC compliant.· Strengthened current design for heavy industrial loads· Designed in according with the requirements of IEC 62314· Zero-crossing (resistive loads) or instantaneous (inductive loads) output

When ordering, the user must state:Load rating1. Rated input voltage 2. Rated working current control mode selection: (optional below)1. Manual potentiometer adjustment: 2.2 - 4.7 KAutomatic control model: 4-20 maAutomatic control model: 1 - 5 VDC, 2 - 10 VDCProduct introduction1. Multiple LED indicator lights on the panel display the working status and fault causes of the voltage regulator, which is convenient for timely maintenance in case of fault.2. The PC board adopts SMD chip, with good anti-interference, low failure rate and no interference.3. Slow start function is included to make the original more stable and durable when changing rapidly.4. Proportional linear output, accurate temperature control, accuracy 0.3%, meet the requirements of various loads.5. The whole machine is made of aluminum alloy, with small volume, good heat dissipation effect and 100% guiding fan for airflow heat dissipation.6. Input mode: 4-20 mA, DC 1-5 V, DC 2-10 v. the three modes are freely switched and selected by p 1 jump without changing the host.7. All series are equipped with high-speed fuse and overheat stop output protection switch to protect the power regulator.8. Working conditionsAmbient temperature: - 20 ～ 65 ℃Relative humidity: - 20-75% RH, no water condensationAltitude: lower than 1000 meters, more than 1000 meters, according to GT / T 3859.1 - 2013 (5.3) standard derating use9. The input power supply voltage at AC 1 and AC 2 terminals of PC board is AC 200 ~ 240 v.10. There is no phase sequence relationship between the main power supply and the working voltage of PC board, so it is easy to use (automatic identification of 50 Hz ~ 60 Hz).11. The air convection hole and cooling fan must be installed in the closed control box. If the heat dissipation is poor, please lower than 70%Otherwise, the overheat protection function of the power controller will be started and the output will be stopped.12. Please check whether the fan works normally from time to time. If not, you need to remove the fan fault before putting it into normal use.Precautions before installation and useBefore installation, please check whether the model and specification of the voltage regulator are consistent with the order requirements. If not, please contact the supplier for replacement.Before installation, please check whether the voltage regulator is damaged, the screw is loose, and the wiring falls off.Load common line can not be connected to zero line or ground, otherwise SCR will be unable to turn off and lose control.Please read the manual carefully before installation.(this product is designed with ZL 20072 0128369.6 structure patent and 2.0082 e + 12 radiator patent.)